CVE-2026-74713
Description détaillée
In the Linux kernel, the following vulnerability has been resolved: vhost_iotlb: bound map allocation in add_range vhost_iotlb_add_range_ctx() only retires an old entry when the table has a non-zero limit, has exactly reached that limit and has VHOST_IOTLB_FLAG_RETIRE set. Non-retiring tables can keep allocating entries after reaching their configured limit. Existing vhost devices allocate their IOTLB with max_iotlb_entries from vhost.c, which defaults to 2048 and is tunable by module parameter. Use the caller-provided limit at the allocation point instead of adding a separate default in the common IOTLB helper, and reject non-positive values in vhost paths that can report an error. Other vhost IOTLB users should not create zero-limit tables when entries can be populated from userspace or guest-controlled requests. Add caller-side max_iotlb_entries parameters for mlx5 vDPA, VDUSE and vhost-vDPA. Reject non-positive VDUSE and vhost-vDPA values, and require at least two entries for vdpa_sim and mlx5 vDPA paths that install full-range mappings, since those mappings are split into two IOTLB entries. Handle full-range mappings in the common helper by checking that the IOTLB can hold both split entries before inserting the first half. This avoids returning an error after leaving a half mapping behind. When the table is full, keep the existing retire behavior for retiring tables and return -ENOSPC for non-retiring tables. Reuse the retired map node instead of freeing it and allocating a replacement, so a stream of IOTLB updates cannot keep forcing GFP_ATOMIC allocations after the table has reached its limit. If a zero-limit IOTLB still reaches the common helper, treat it as a configuration error and return -EINVAL. I found this bug myself, though the patch was written with AI assistance.
Dernières Vulnérabilités
CVE-2026-74733
In the Linux kernel, the following vulnerability has been resolved: gpio: pca953x: fix pca953x_irq_bus_sync_unlock regmap lock Locking is disabled in the regmap config as this driver uses its own lock. This means that all calls to regmap functions (read or write) must hold the i2c_lock. The function pca953x_irq_bus_sync_unlock() did not do this, and it was therefore possible that multiple threads could cause an incorrect register to be read/written. A previous patch partly fixed this, but only protected the write to the interrupt mask register, and not the read from the direction register.
CVE-2026-74732
In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Check for tg ops in dce110_set_avmute Some older DCE timing generators do not implement is_tg_enabled in their ops table. Calling it unconditionally when waiting for AV mute frames causes a NULL pointer dereference on Southern Islands dGPUs when turning the display off over HDMI. Check that tg and the required ops exist before waiting for frames. (cherry picked from commit 2686a0c0aaa07bec2e24131835cf27b5fd4935a5)
CVE-2026-74731
In the Linux kernel, the following vulnerability has been resolved: sched_ext: Skip sub-disable teardown for never-linked sub-schedulers A sub-scheduler enable can fail before scx_link_sched() links the sched into the hierarchy, e.g. when the parent is already being disabled, and cleanup still runs the full scx_sub_disable(). That is racy against root disable: drain_descendants() is the only ordering between a sub's disable-time task walk and root disable's all-task teardown, and an unlinked sub is invisible to it. Root's teardown can thus run between the never-linked sub's drain and its walk, exiting every task to no scheduler. The walk then trips the membership WARN and re-homes the exited tasks onto the dying hierarchy, a use-after-free. Skip the cgroup ownership reset and the task walk if @sch was never linked, indicated by the empty ->sibling as unlinking only happens later in the same function. The membership WARN remains valid: a linked sub is always waited on by an ancestor's drain.